County of Broward (FL)

Codes

NEC Code Version

2020

Fire Code Version

2018 Building Code

Code List

2023 8TH EDITION FLORIDA BUILDING CODE: BUILDING

2023 8TH EDITION FLORIDA BUILDING CODE: RESIDENTIAL

2023 8TH EDITION FLORIDA BUILDING CODE: MECHANICAL

2023 8TH EDITION FLORIDA BUILDING CODE: PLUMBING

2023 8TH EDITION FLORIDA BUILDING CODE: FUEL GAS

2023 8TH EDITION FLORIDA BUILDING CODE: ENERGY CONSERVATION

2023 8TH EDITION FLORIDA BUILDING CODE: EXISTING BUILDING

2023 8TH EDITION FLORIDA BUILDING CODE: ACCESSIBILITY

2023 8TH EDITION FLORIDA FIRE PREVENTION CODE (NFPA)

2020 NATIONAL ELECTRIC CODE (NEC)

ASCE Code Specification

ASCE 7-16

SolarAPP+ & submittal

SolarAPP+ Status

Targeted

Any SolarAPP+ Restrictions

1

SolarAPP+ Restrictions

MPU,MPU,MPU,Derate,Derate,Derate

How Many Plansets Required

2

Revision Required

0

Rough Inspection

Rough Electrical

New Planset Required For Module Swap

0

Stamps

Ee Stamp Required On SLD

Yes

Wet Stamps Required

Wet Structural,Wet Electrical

Structural Calculations Required

Yes

Ee Stamp Notes

EE Stamp required. Load calcs require EE Stamp, if applicable.

Stamp Location On Plans

Unspecified

Date On Stamps

Expiration Date

Fire setbacks

Fire Setback Enforced

1

Setback Notes

Standard

Structural & loads

Wind Speed

170

Wind Notes

Exposure Category C ; HVHZ

Snow Load

0

Reducible Snow Load Allowed

1

Max Attachment Spacing

96

Structural Notes

* All pages PE & EE stamped, not separated. Wet stamped and signed, 2 sets of stamped documents mailed to 3590 NW 54th St #3, Fort Lauderdale, FL 33309, USA * We enforce the FBC 2020, NEC 2017, (FFPC) -7th edition, specifically Chapter 11.12 & NFPA 70, ed. 2017 (Pay special attention to the Roof Access section 11.12.2.2 in NFPA 1, 7th edition) * Digital stamp is also needed for an online Environmental permit. * Stamped Special Inspector Form Required * PE calcs must provide site specific attachment strength detail and lag bolt pull out calculations.

This AHJ does not accept stamped signature. Wet signature required

Minimum Ground On Roof

#10

Electrical

Electrical Load Calcs Required

Derates

Allowed POI

PV Breaker,Load Side Taps,Line Side Taps

Panel Schedule Required

Partial Home Backup

Temperature Rating

90

De Rating Ampacity

0.96

Battery / ESS

Unique Battery Placards Needed

0

ESS Notes

Standard

Separate ESS Disconnect Required

ESS Disconnect

ESS Elevation Detail Required

No

Plan set

Plan Set Requirements

ATTACH AND FILL OUT SIF

Derate required load calcs signed by EE, Requirements for electronic signing and sealing of plans and documents are set forth by the regulations of the appropriate professional board of licensing. The ePermit system allows for documents to be signed and sealed by two methods. Electronic Sign and Sea The “electronic sign and seal method utilizes the esign process that is built into the ePermit system. This method is free, but requires a one page signature document to be printed and manually signed and sealed by the registered professional(s). The signature document(s) must be submitted in original form to conform with the professional licensing regulations. Digital Sign and Seal The digital sign and seal method requires purchasing a subscription from a third party digital signature provider, such as Globalsign and Verisign. When we receive a document that has been signed and sealed digitally, we can instantly confirm the documents validity which allows for immediate processing. The advantage of digital sign and seal is it eliminates the need for a paper document to be produced and distributed, allowing for 100% paperless and streamlined processing. Provide flashing documentation along with fire classification.

Roof Plan

* Provide visual Array Wind zones Exposure on the roof with Exposed, Non-Exposed, Edge, module clearance and nominal installation spans, cantilever dimensions and Fire setbacks. * Clearly show identifiable Panel Module stand/mounting Locations attachments

Attachment Detail

If not using rail attachment system, make sure all callouts of the word "rail" are removed from the page

Electrical Diagram

Taps

• Piercing taps NOT ALLOWED
• Utilize Polaris taps

Label Page

FLORIDA 2020 CAD BLOCK

Custom Placards Required

1

Placards Notes

Ground mount

Ground Mount Fencing Required

Mesh/Scrim

Ground Mount Notes

1\. Do you require ground mounts to have additional fencing or meshing protecting the array? * We enforce the NEC 2017